Ⅰ PLC問題，液體自動混合裝置通電初始，閥門Y1、Y2、Y3關閉，Y4打開10秒，將容器內殘留液放空。
這個一般沒人給你寫，除非給報酬。
Ⅱ 西門子PLC，s7-200.兩種液體混合攪拌控制，其功能要求如下：
你是要程序還是要什麼？ 你這個只是簡單的邏輯控制 好好想想 不難寫
Ⅲ 基於PLC的液體自動混合控制系統的畢業設計
我這兒有一份，給你發過去了，你看看符合要求嗎！
Ⅳ 2種液體自動均勻混合PLC控制系統設計（請教各位前輩多多指教幫助）
也不要請教道這樣無恥的地步啦，這種做法其實是領了項目叫別人白幹活，誰會這么傻呀，有活賺錢也應該考慮一下人家做技術人員的吃飯問題啦
Ⅳ 兩種液體混合裝置PLC控製程序設計
2. 控制要求：有兩種液體A、B需要在容器中混合成液體C待用，PLC開始運行時清空容器。（1）按下啟動信號內，閥門A打開，注入液體A；到達I位置時，閥門A關閉，閥門B打開，注入液體B；到達H時，閥門B關閉，容器內液體進行攪拌，5s正轉，4s反轉，循環3次後停止攪拌，開容始加熱，15s後停止加熱；打開閥門閥門C，釋放液體C；當最低位液位感測器L=0時，關閉閥門進入下一個循環。（2）按下暫停按鈕,要求停止攪拌，停止加熱；按下繼續按鈕要求系統從剛才暫停處接著運行。（3）按下停止按鈕，所以操作都停止，並且將容器內的液體全部釋放完，然後關閉閥門C。 3. 按照要求編寫程序並模擬調試。
Ⅵ 液料自動混合控制 PLC 課程設計 包括主電路圖 PLC接線圖 輸入輸出圖麻煩各位幫忙了,暫時沒分了，謝謝了啊
請問哈你的問題搞定沒有呀。
你需要繼電器的電路圖，還是需要PLC的電路圖呀，PL需要什麼樣的PLC呀
Ⅶ 基於PLC的液體自動混合控制系統的畢業設計
我是山東
威海
德慶
工業電器威海自動化的，想幫你，但你說的好籠統,不知道怎麼下手,沒有一點思路可言.
Ⅷ 摘要翻譯，不要工具翻譯的
With the development of economy and the progress of the society, requirements for automatic instrial proction continued to improve. In medicine, food, chemical instries, often need to put more dangerous liquid toxic, flammable and explosive necessary processing in time and in the right conditions so as to obtain a proct, but these processes have been carried out in human monitoring or manual operation, so that the working environment is very bad. The design of the main use of PLC to achieve the control device and the configuration of the three kinds of liquid mixture as an example, device parameter set through PLC automatic mixed automatic operation completion fluid, reces the risk of manual operation. This paper introces the basic design requirements of various liquids automatic mixing and technical analysis, and also introces the control technology of PLC and configuration, and mainly on the "design of the automatic mixing device control and configuration of various liquid" PLC implementation is analyzed and discussed based on. The instrial design using programmable logic controller (PLC) and configuration (Configure) automatic control technology to solve instrial monitoring a variety of automatic liquid mixing control problems. Using a combination of PLC control and configuration monitoring technology, to realize the automatic process of three or more liquids in certain proportion are added in mixing, stirring, heating device and emissions. The design of the three kinds of liquid mixture as an example, the main elements of the design include: analysis and design of electrical principle diagram of process analysis and arrangement, device control and configuration of the design, hardware connection and connection, the trapezoidal chart analysis and design, design and analysis of defects and its situation. After a number of debugging and modification, the design realizes the automatic add liquid, automatic mixing, automatic heating and automatic control function of multi liquid mixing device, but also realizes the manual and automatic switch or a combination of function. In addition, this paper also discusses the difficulties encountered in the design, the design of the shortcomings and the foreground of the design.