1. 机械英语的翻译，谁可以帮忙一下啊，万分感谢
First, import measurement system categories: USA - West (Sealo1) Corporation, the United States - Flowserve Corporation, USA - Dura company John John Crane International (International) Heavy Instries, the United States -博格瓦纳(Borg-wanter) UK -- Crane (Crane Packing), Germany - Bergman (Burgmann) company, Denmark - Grundfos, Sweden - Alfa valve (AFLA), Canada - Pacific & richard Company, Japan - Piranesi company, Japan - carbon Advantech PAC-international sealed Seiko Company, Japan - Eagle (Eagle) company, United Kingdom -弗莱克西box (Flexibox) companies, providing technical advice, sample mapping customization, repair facilities, special services. In ensuring that under the premise of quality, price is only 30% of the import price -40%. Second, pump categories: 101,103,104,105,106,108,109,110,111,114,151,152,156,168,169,1527,1528,523,524,43 type, F type, Type Dalian, Shenyang-based, P-type, GX, GY, EX, EY, FBD, BIA type, M7-series, WM104, WM108, WM208, etc.. Third, reactor type: 201,202,203,204,205,205 A, 211,206,212,2 CW2T, 3J02J, FM-I, M45KL, HSHL-D, VRA, BRO, PACIFIC-560, PACIFIC-582, PACIFIC-583 and so on. Fourth, accessories category: United States DuPont Kalrez 6375/7075 desflurane poly-wide rubber O-ring, the United States GREENE TWEED company CHEMRAZ 505/605 O-ring, fluorine rubber, silicone rubber, oil NBR rubber, all-inclusive fluoride "O" ring seal, bronze PTFE, PTFE V-ring, support ring, gaskets, PTFE gasket kits rubber composites, PTFE silicon carbide, silicon nitride, alumina, chromium oxide , spraying ceramic seal ring. Loaded carbide inserts, carbide sprayed Ni60 surfacing hard seal ring. Baptist antimony carbon graphite seal ring and filled with all kinds of PTFE sealing ring, such as accessories and more than the special-shaped pieces of various materials processing. Shaft above have a variety of specifications, such as 12-150.
2. 机械密封是什么
中文名称：机械密封 英文名称：mechanical seal 定义：由至少一对垂直于旋转轴线的端面回在流体压力和补偿机构弹答力（或磁力）的作用以及辅助密封的配合下，保持贴合并相对滑动而构成的防止流体泄漏的装置。 应用学科：机械工程（一级学科）；机械零件（二级学科）；机械密封（三级学科）
3. 各路高手，哪个能提供液压专业英语词汇，包括缸，阀，泵，马达，密封件，连接件等
液压专业英语词汇
acceptable conditions许用工况
actual conditions实际工况
actual force实际输出力
air contamination空气污染
air consumption耗气量
air conditioner unit空气处理单元
air filter空气过滤器
adjustable restrictive valve可调节流阀
amplifier放大器
amplitude ratio幅值比
analogue amplifier模拟放大器
anti-corrosive quality抗腐蚀性
automatic cycle自动循环
axial piston pump轴向柱塞泵
back pressure背压
bladder accumulator气囊式蓄能器
bleed line放气管路
bonded washer组合垫圈
breakout pressure启动压力
butterfly valve蝶阀
cartridge valve插装阀
cavitation气穴
charge pressure充油压力
check valve单向阀
circle循环
circuit diagram回路图
clamper管卡
closed circuit闭式回路
collapse pressure压溃压力
compensator避震喉
composite seal复合密封件
continuous working conditions连续工况
control of pump泵的控制
control console操作台
control panel控制屏
cooler冷却器
counterbalance valve平衡阀
cracking pressure开启压力
cushioning缓冲
cylinder缸
cycling speed循环速度
De-energizing of solenoid 电磁铁释放
density密度
diaphragm valve膜片阀
differential circuit差动回路
differential cylinder差动缸
differential pressure instrument压差计
digital amplifier数字放大器
direction of rotation旋转方向
directly operated type直动式
displacement排量
dither颤振
double-acting cylinder双作用缸
Double throttle check valve 双单向节流阀
drain line泄油管路
drift漂移
drive shaft coupling联轴器
dwell phase停止工步
plex filter双筒过滤器
efficiency效率
effective filtration area有效过滤面积
elastomer seal弹性密封件
elbow弯头
electrical pressure transcer压力传感器
external leakage外泄漏
extend stroke外伸行程
filter pressure drop过滤器压降
fitting；connection接头
fixed restrictive valve固定节流阀
flared fitting扩口式接头
flash point闪点
flexible hose软管
flange connection法兰接头
flange mounting法兰安装
flow-combining valve集流阀
flow control valve流量控制阀
flow control circuit调速回路
flow divider valve分流阀
flow gain流量增益
flow limit流量极限
flow line管路
flow meter流量计
flow pass流道
flow rate流量
Flow valve 流量阀
flower factor流量系数
foot mounting底座安装
force输出力
four-way valve四通阀
free position自由位
frequency response频率响应
function diagram功能图
gate valve闸阀
gear pump齿轮泵
global(ball) valve球阀
graphical symbol图形符号
heat exchanger热交换器
heater加热器
hydraulic lock液压锁紧
hydraulic motor液压马达
hydraulic power流体传动
hydraulics液压技术
hydrodynamics液力技术
hydropneumatics气液技术
hysteresis滞环
hydraulic amplifier液压放大器
hydraulic controlled type液控式
instantaneous conditions瞬态工况
internal leakage内泄漏
inlet pressure进口压力
inced pressure负载压力
kinematic viscosity运动粘度
laminar flow层流
lap遮盖
leakage泄漏
limited conditions极限工况
linearity线性度
linear region线性区
liquid contamination液体污染
liquid level measuring instrument液位计
lubricator油雾气
manually operated type手动式
manifold block油路块
mechanically controlled type机械控制式
mechanical seal机械密封
meter-in circuit进口节流回路
meter-out circuit出口节流回路
Manifold block 集成块
needle valve针阀
neutral position中位
nitrile butadiene rubber；NBR丁腈橡胶
noise level噪声等级
nominal filtration rating公称过滤精度
nominal pressure公称压力
nozzle flapper喷嘴挡板
null bias零偏
null drift零漂
null(quiescent) leakage零位内泄漏
one-way restrictive valve单向节流阀
opening开口
open circuit开式回路
operating conditions运行工况
operating pressure运行压力
outlet pressure出口压力
over lap正遮盖
override pressure调压偏差
override control优先控制
packing seal填料密封
peak pressure峰值压力
phase工步
phase lag相位移
Pilot valve 先导阀
pilot pressure控制压力
pilot-controlled check valve液控单向阀
pilot-operated type先导式
Pilot operated check valve 液控单向阀
piston pump柱塞泵
pilot line控制管路
pipe-work管路布置
piston seal活塞密封
polytetrafluoroethene；PTFE聚四氟乙烯
poppet valve锥阀
portable particle counter便携式颗粒检测仪
port油口
Position feedback 位置反馈
power station液压泵站
pre-charge pressure充气压力
pressure control circuit压力控制回路
pressure drop；differential pressure压降
pressure gauge压力表
Pressure relief valve 压力溢流阀
pressure switch压力开关
pressure time diagram压力－时间图
pressure relief valve压力控制阀
pressure relief valve溢流阀
pressure recing valve减压阀
Progressive flow 渐增流量
Proportional valve 比例阀
proof pressure耐压试验压力
pulse generator脉冲发生器
quick release coupling快换接头
radial seal径向密封
rapid advance phase快进工步
rapid return phase快退工步
rated conditions额定工况
rated flow额定流量
rated pressure额定压力
rear end无杆端
Rectifier plate 节流板
recer fitting异径接头
replenishing line补液管路
reservoir fluid capacity油箱容量
resolution分辨率
retract stroke内缩行程
return line回油管路
repeat ability重复性
reprocibility复现性
rigid tube硬管
ripple波动
rod end有杆端
rod seal活塞杆密封
rotary seal旋转密封
Rotary knob 旋钮
rust protection防锈性
safety circuit安全回路
sandwich valve叠加阀
Sandwich plate valve 叠加阀
sealed reservoir闭式油箱
sensor传感器
sequence valve顺序阀
servo-valve伺服阀
shut-off valve截止阀
shuttle valve梭阀
silencer消声器
single-acting cylinder单作用缸
slide valve滑阀
solid contamination固体颗粒污染
Solenoid valve 电磁阀
speed regulator valve调速阀
static pressure静压力
sticking液压卡紧
steady-state conditions稳态工况
stiffness刚度
sub-plate底板
sub-plate valve板式阀
Sub-plate mount 板式安装
suction pressure吸入压力
supply flow供给流量
surge pressure冲击压力
system pressure系统压力
symbols for hydraulic and pneumatic components液压气动元件图形符号
symbols for fluid logic devices流体逻辑元件图形符号
symbols for logic functions逻辑功能图形符号
symmetry对称度
synchronizing circuit同步回路
telescopic cylinder伸缩缸
thermostat温度控制器
threshold阈值
Throttle valve 节流阀
transfer function传递函数
turbulent flow紊流
under lap负遮盖
unloading valve卸荷阀
valve阀
valve element阀芯
valve element position阀芯位置
variable displacement pump变量泵
valve pressure drop阀压降
valve polarity阀极性
viscosity粘度
water content含水量
welded fitting焊接式接头
wiper seal；scraper防尘圈密封
working cycle工作循环
working pressure工作压力
working phase工作工步
working stroke工作行程
working line工作管路
vane pump叶片泵
zero position零位
zero lap零遮盖
二、介质类
Emulsion 乳化液
Inhibitor缓蚀剂
Phosphate ester (HFD-R) 磷酸甘油酯
Synthetic lubricating oil 合成油
Water-glycol (HFC) 水-乙二醇
三、液压安装工程
Abrasion 摩擦
Argon 氩气
Butt welding 对接焊
Contamination 污染
Creep爬行
Dipping process 槽式酸洗
Extension （活塞杆）缩回
Failure 失效
Flushing 冲洗
Grout 灌浆
Inert gas welding 惰性气体焊
Jog 点动
Malfunction 误动作
Nitric acid 柠檬酸
Passivity 钝化
Pickling 酸洗
Retract（活塞杆）伸出
Re-circulation 循环
Socket welding 套管焊
四、管接头
Adjustable fittings/swivel nut 旋转接头
Banjo fittings 铰接式管接头
Bite type fittings 卡套式管接头
Bulkhead fittings 长直通管接头
Female connector fittings 接头螺母
Mal stud fittings 端直通管接头
Recers extenders 变径管接头
Tube to tube fittings 接管接头
union 直通接管接头
union elbow 直角管接头
union tee 三通管接头
union cross 四通管接头
Weld fittings 焊接式管接头
五、伺服阀及伺服系统性能参数
accessory 液压辅件
actuator 执行元件
cartridge valve 插装阀
circuit 液压回路
Coil impedance 线圈阻抗
common valve 普通阀
cylinder 液压缸
DDV-direct drive valve 直动式伺服阀
directional valve 方向控制阀
Dither 颤振电流
Dynamic response 动态频响
Flow saturation 流量饱和
flow valve 流量控制阀
Frequency response 频率响应
Hysterics 滞环
hydraulic system 液压系统
Lap 滞后
Linearity 线形度
motor 液压马达
NFPA-National Fluid Power Association 美国流体控制学会
Nozzle flapper valve 喷嘴挡板阀
Null 零位
Null bias 零偏
Null shift 零飘
pressure control 压力控制回路
pressure valve 压力控制阀
pump 液压泵
speed control 流量（速度）控制回路
directional valve control 方向控制回路
Phase lag 相位滞后
position control 定位回路
Pressure gain 压力增益
security control 安全回路
sequeunt circuit 顺序动作回路
Servo-jet pilot valve 射流管阀
Slope 曲线斜坡
superimposed valve叠加阀
Symmetry 对称性
synchronise circuit 同步回路
Threshold 灵敏度
valve 阀、
4. 液压传动术语中英文对照
不好意思，文献没有。。
只有这些词汇。
液压专业英语词汇
acceptable conditions许用工况
actual conditions实际工况
actual force实际输出力
air contamination空气污染
air consumption耗气量
air conditioner unit空气处理单元
air filter空气过滤器
adjustable restrictive valve可调节流阀
amplifier放大器
amplitude ratio幅值比
analogue amplifier模拟放大器
anti-corrosive quality抗腐蚀性
automatic cycle自动循环
axial piston pump轴向柱塞泵
back pressure背压
bladder accumulator气囊式蓄能器
bleed line放气管路
bonded washer组合垫圈
breakout pressure启动压力
butterfly valve蝶阀
cartridge valve插装阀
cavitation气穴
charge pressure充油压力
check valve单向阀
circle循环
circuit diagram回路图
clamper管卡
closed circuit闭式回路
collapse pressure压溃压力
compensator避震喉
composite seal复合密封件
continuous working conditions连续工况
control of pump泵的控制
control console操作台
control panel控制屏
cooler冷却器
counterbalance valve平衡阀
cracking pressure开启压力
cushioning缓冲
cylinder缸
cycling speed循环速度
De-energizing of solenoid 电磁铁释放
density密度
diaphragm valve膜片阀
differential circuit差动回路
differential cylinder差动缸
differential pressure instrument压差计
digital amplifier数字放大器
direction of rotation旋转方向
directly operated type直动式
displacement排量
dither颤振
double-acting cylinder双作用缸
Double throttle check valve 双单向节流阀
drain line泄油管路
drift漂移
drive shaft coupling联轴器
dwell phase停止工步
plex filter双筒过滤器
efficiency效率
effective filtration area有效过滤面积
elastomer seal弹性密封件
elbow弯头
electrical pressure transcer压力传感器
external leakage外泄漏
extend stroke外伸行程
filter pressure drop过滤器压降
fitting；connection接头
fixed restrictive valve固定节流阀
flared fitting扩口式接头
flash point闪点
flexible hose软管
flange connection法兰接头
flange mounting法兰安装
flow-combining valve集流阀
flow control valve流量控制阀
flow control circuit调速回路
flow divider valve分流阀
flow gain流量增益
flow limit流量极限
flow line管路
flow meter流量计
flow pass流道
flow rate流量
Flow valve 流量阀
flower factor流量系数
foot mounting底座安装
force输出力
four-way valve四通阀
free position自由位
frequency response频率响应
function diagram功能图
gate valve闸阀
gear pump齿轮泵
global(ball) valve球阀
graphical symbol图形符号
heat exchanger热交换器
heater加热器
hydraulic lock液压锁紧
hydraulic motor液压马达
hydraulic power流体传动
hydraulics液压技术
hydrodynamics液力技术
hydropneumatics气液技术
hysteresis滞环
hydraulic amplifier液压放大器
hydraulic controlled type液控式
instantaneous conditions瞬态工况
internal leakage内泄漏
inlet pressure进口压力
inced pressure负载压力
kinematic viscosity运动粘度
laminar flow层流
lap遮盖
leakage泄漏
limited conditions极限工况
linearity线性度
linear region线性区
liquid contamination液体污染
liquid level measuring instrument液位计
lubricator油雾气
manually operated type手动式
manifold block油路块
mechanically controlled type机械控制式
mechanical seal机械密封
meter-in circuit进口节流回路
meter-out circuit出口节流回路
Manifold block 集成块
needle valve针阀
neutral position中位
nitrile butadiene rubber；NBR丁腈橡胶
noise level噪声等级
nominal filtration rating公称过滤精度
nominal pressure公称压力
nozzle flapper喷嘴挡板
null bias零偏
null drift零漂
null(quiescent) leakage零位内泄漏
one-way restrictive valve单向节流阀
opening开口
open circuit开式回路
operating conditions运行工况
operating pressure运行压力
outlet pressure出口压力
over lap正遮盖
override pressure调压偏差
override control优先控制
packing seal填料密封
peak pressure峰值压力
phase工步
phase lag相位移
Pilot valve 先导阀
pilot pressure控制压力
pilot-controlled check valve液控单向阀
pilot-operated type先导式
Pilot operated check valve 液控单向阀
piston pump柱塞泵
pilot line控制管路
pipe-work管路布置
piston seal活塞密封
polytetrafluoroethene；PTFE聚四氟乙烯
poppet valve锥阀
portable particle counter便携式颗粒检测仪
port油口
Position feedback 位置反馈
power station液压泵站
pre-charge pressure充气压力
pressure control circuit压力控制回路
pressure drop；differential pressure压降
pressure gauge压力表
Pressure relief valve 压力溢流阀
pressure switch压力开关
pressure time diagram压力－时间图
pressure relief valve压力控制阀
pressure relief valve溢流阀
pressure recing valve减压阀
Progressive flow 渐增流量
Proportional valve 比例阀
proof pressure耐压试验压力
pulse generator脉冲发生器
quick release coupling快换接头
radial seal径向密封
rapid advance phase快进工步
rapid return phase快退工步
rated conditions额定工况
rated flow额定流量
rated pressure额定压力
rear end无杆端
Rectifier plate 节流板
recer fitting异径接头
replenishing line补液管路
reservoir fluid capacity油箱容量
resolution分辨率
retract stroke内缩行程
return line回油管路
repeat ability重复性
reprocibility复现性
rigid tube硬管
ripple波动
rod end有杆端
rod seal活塞杆密封
rotary seal旋转密封
Rotary knob 旋钮
rust protection防锈性
safety circuit安全回路
sandwich valve叠加阀
Sandwich plate valve 叠加阀
sealed reservoir闭式油箱
sensor传感器
sequence valve顺序阀
servo-valve伺服阀
shut-off valve截止阀
shuttle valve梭阀
silencer消声器
single-acting cylinder单作用缸
slide valve滑阀
solid contamination固体颗粒污染
Solenoid valve 电磁阀
speed regulator valve调速阀
static pressure静压力
sticking液压卡紧
steady-state conditions稳态工况
stiffness刚度
sub-plate底板
sub-plate valve板式阀
Sub-plate mount 板式安装
suction pressure吸入压力
supply flow供给流量
surge pressure冲击压力
system pressure系统压力
symbols for hydraulic and pneumatic components液压气动元件图形符号
symbols for fluid logic devices流体逻辑元件图形符号
symbols for logic functions逻辑功能图形符号
symmetry对称度
synchronizing circuit同步回路
telescopic cylinder伸缩缸
thermostat温度控制器
threshold阈值
Throttle valve 节流阀
transfer function传递函数
turbulent flow紊流
under lap负遮盖
unloading valve卸荷阀
valve阀
valve element阀芯
valve element position阀芯位置
variable displacement pump变量泵
valve pressure drop阀压降
valve polarity阀极性
viscosity粘度 water content含水量
welded fitting焊接式接头 wiper seal；scraper防尘圈密封
working cycle工作循环 working pressure工作压力
working phase工作工步 working stroke工作行程
working line工作管路 vane pump叶片泵
zero position零位 zero lap零遮盖
一． 阀类
分流阀 flow divider valve 截止阀 shut-off valve
球阀 global(ball) valve 针阀 needle valve
闸阀 gate valve 膜片阀 diaphragm valve
蝶阀 butterfly valve 阀 valve
底板 sub-plate 油路块 manifold block 板式阀 sub-plate valve 叠加阀 sandwich valve 插装阀 cartridge valve 滑阀 slide valve 锥阀 poppet valve 阀芯 valve element 阀芯位置 valve element position
单向阀 check valve
液控单向阀 pilot-controlled check valve
梭阀 shuttle valve
压力控制阀 pressure relief valve
溢流阀 pressure relief valve
顺序阀 sequence valve
减压阀 pressure recing valve
平衡阀 counterbalance valve
卸荷阀 unloading valve
流量控制阀 flow control valve
方向控制阀（directional valve）
液压辅件（accessory）
普通阀（common valve）
Solenoid valve 电磁阀
Check valve 单向阀
Cartridge valve 插装阀
Sandwich plate valve 叠加阀
Pilot valve 先导阀
Pilot operated check valve 液控单向阀
Sub-plate mount 板式安装
Manifold block 集成块
Rotary knob 旋钮
Rectifier plate 节流板
Servo valve 伺服阀
Proportional valve 比例阀
Position feedback 位置反馈
Progressive flow 渐增流量
De-energizing of solenoid 电磁铁释放
固定节流阀 fixed restrictive valve
可调节流阀 adjustable restrictive valve
单向节流阀 one-way restrictive valve
调速阀 speed regulator valve
分流阀 flow divider valve
集流阀 flow-combining valve
DDV-direct drive valve 直动式伺服阀
二、介质类
Phosphate ester (HFD-R) 磷酸甘油酯 Water-glycol (HFC) 水-乙二醇
Emulsion 乳化液 Inhibitor缓蚀剂 Synthetic lubricating oil 合成油
三、液压安装工程
Abrasion 摩擦 Argon 氩气 Butt welding 对接焊
Contamination 污染 Creep爬行 Dipping process 槽式酸洗
Extension （活塞杆）缩回 Failure 失效
Flushing 冲洗 Grout 灌浆 Inert gas welding 惰性气体焊
Jog 点动 Malfunction 误动作 Nitric acid 柠檬酸
Passivity 钝化 Pickling 酸洗 Retract（活塞杆）伸出
Re-circulation 循环 Socket welding 套管焊
四、管接头
Adjustable fittings/swivel nut 旋转接头
Banjo fittings 铰接式管接头
Bite type fittings 卡套式管接头
Bulkhead fittings 长直通管接头
Female connector fittings 接头螺母
Mal stud fittings 端直通管接头
Recers extenders 变径管接头
Tube to tube fittings 接管接头
union 直通接管接头
union elbow 直角管接头
union tee 三通管接头
union cross 四通管接头
Weld fittings 焊接式管接头
五、伺服阀及伺服系统性能参数
Dynamic response 动态频响
DDV-direct drive valve 直动式伺服阀
NFPA-National Fluid Power Association 美国流体控制学会
Phase lag 相位滞后
Nozzle flapper valve 喷嘴挡板阀
Servo-jet pilot valve 射流管阀 Dither 颤振电流
Coil impedance 线圈阻抗
Flow saturation 流量饱和
Linearity 线形度 Symmetry 对称性
Hysterics 滞环 Threshold 灵敏度
Lap 滞后
Pressure gain 压力增益
Null 零位
Null bias 零偏
Null shift 零飘
Frequency response 频率响应
Slope 曲线斜坡
祝你取得好成绩！
5. 英文“code" 翻译成德文也是”code"吗
基础英汉词典
code [kəud]
n.准则；密码，代码 vt.把…编码 机械密封.机封.水封.轴封
Fundset 德汉词典
Code
[der] pl.Codes 密码。编码。法典。=Kode
6. 有人知道机械密封的型号是EF30J4A表示什么意思吗
1. EF，应该是英文单词extremely fine，指的是精度很高的意思；
2. 30，应该指的是机械密封的标称内径；
3. J4，不是很肯定，感觉应该是机械密封的厚度，你再根据实际情况确认下；
4. A，应该是系列设计中的一个序列号而已吧；
供参考，如有帮助，请采纳
7. 英语翻译 这里的code是密码的意思,德文也有code这个词而且也是“码”的意思吗
基础英汉词典
code [kəud]
n.准则；密码,代码 vt.把…编码 机械密封.机封.水封.轴封
Fundset 德汉词典
Code
[der] pl.Codes 密码.编码.法典.=Kode
8. 关于机械类的英语翻译，谁能帮帮忙
机械密封含药系统
主泵机械密封1 + 2:
数量的机械密封:4台
设计压力:25酒吧
马克斯。压力:40酒吧
介质温度(t1):186 -°C
设计温度:200°C
速度(n):5200 1 /分钟
轴直径为151836毫米
直径的轴袖:152 H6
API-Plan计划23 +夹克的冷却
力矩传输:收缩碟
轴袖将由区域
中等:给水
冷却水:闭路冷却water-sytem;软化水(pH 7、8 - 8次,2)
冷却水温度在使用/设计:36°39°C / C
机械密封:单作用、双向、设计:Cartridge-unit,轴套筒(将由区域)、钳板、密封罩、完全安装安装没有调整,incl. thermostop
——游泳掐戒指
-和泵环
- - - - - - - - - - - - jacket-cooling循环
——反作用:+ / - 3毫米
主泵机械密封,3 + 4:
数量的机械密封:4台
设计压力:25酒吧
马克斯。压力:40酒吧
介质温度(t1):186 -°C
设计温度:200°C
速度(n):6700 1 /分钟
轴直径为103 g6
直径的轴袖:103 H6
API-Plan计划23 +夹克的冷却
力矩传输:收缩碟
轴袖将由区域
中等:给水
冷却水:闭路冷却water-system;软化水(pH 7、8 - 8次,2)
冷却水温度在使用/设计:36°39°C / C
机械密封:单作用、双向、设计:Cartridge-unit,轴套筒(将由区域)、钳板、密封罩、完全安装安装没有调整,incl. thermostop
——游泳掐戒指
-和泵环
- - - - - - - - - - - - jacket-cooling循环
——反作用:+ / - 3毫米
9. 机械密封中的英语词组，帮翻译一下！
止回阀套管
放电阀芯
放电拟合
洗衣机专用
环收紧
减震配件组装
Tinb惠普
幻灯片收紧
环
刮刀
卡簧
间隔
环密封
环形密封
张力环
支承环
包装杯
环形弹簧
洗衣机专用
包装杯
密封环
春季杯
垫片，全密封103A条，
内六角螺丝
弹簧垫圈
球面滚子接近
滚子轴承
滚子轴承
平键
平键
卡簧
卡簧
卡簧
卡簧
导向环
'Turcon Stepseal K的垫片
O形圈
O形圈
O形圈
密封
春季型直脚
平垫圈
平垫圈的螺纹孔
10. 轮机英语日常用语
船舶英语
目 录
一.职位及工种
(Titles and type of work) ••••• 1
二、柴油机类
(Words about diesel engine) ••••• 3
三、船舶机械类
(Words about marine machinery) •• 11
四、阀门(Words about valve) •••• 14
五、泵类(Words about pump) •••••••••• 16
六、甲板机械类（Deck machinery）•••••• 18
七、工具类(Word about tools) •••••••• 20
八、常用物料(Material in common use) 26
九、常用紧固件
(Part of fixation in common use) ••• 28
十、常用油类(Oil in common use) •••••28
十一、常用量词
(Quantifier in common use) •••••••••29
十二、国家名称(Name of country) 。 30
十三、常用缩语
(abbreviation in common use) •••••31
十四、船用动态常用单词(marine tends word) 32
十五、船舶机电设备操作词汇
(manipulate of marine equipment) •33
十六、故障常用单词
(words about malfunction) ••••• 35
十七、保养检修常用词汇
(Words about maintain and examination) 38
十八、常用数字(Numeral in common use) 40
十九、时间、季节与方向
(Time、Season and Direction) •••••42
二十常用词组（Phrases in common use）•45
二十一、常用动词和例句
(Verb in common use and example) ••••48
二十二、问候和常用表达语
(Greeting and common expression) ••••67
二十三、主机提交过程用语
(Delivery expressions for main engine) 68
二十四、空压机和空气系统用语
(Air compressor and Air system) •••• 75
二十五、锅炉提交用语
(Delivery expressions for boiler) •••77
二十六、锚绞车提交过程用语(Delivery expressions for anchor windlass) 79
二十七、舵机提交过程用语
(Steering gear delivering) ••• 87
二十八、付机提交过程用语
（Delivery expression for A/E）••••• 91
二十九、救生艇提交过程用语
(Delivery expressions for lifeboat) ••92
三十、其他提交项目
(Delivery expressions for other items) •••95
三十一、甲板机械系泊试验
(Mooring test for deck machinery) ••••••••96
三十二、机舱设备系泊试验
(Mooring test for the equipment in E/R) •••98
三十三、谈论故障常用语
（Expressions for trouble）••••••••••••100
三十四、谈论检修常用语
(Expressions for overhaul) ••••••••••••101
三十五、谈论试验和检验
(Talking about test & check) •••••••••••103
三十六、谈论技术要求
(Talking about technology required) •••105
一．职位及工种(Titles and type of work)
1．船长 Captain
2．大副 Chief officer
3．二副 Second officer
4．三副 Third officer
5．四副 Fourth officer
6．水手长 Boatswain
7．水手 Sailor & Seaman
8．木匠 Carpenter
9．轮机长 Chief engineer
10．大管轮 Second engineer
11．二管轮 Third engineer
12．三管轮 Fourth engineer
13．机匠长 Chief motorman
15．机匠 Fitter
16．加油工 Oil man
17．大电 Chief electrician
18．电工 Electrician
19．车间主任 Workshop director
20．工长 Section chief
21．班长 Fore man
22．钳工 Fitter
23．主管工程师 Engineer in charge
24．机务&船东 Superintendent &Super &Owner
25．助理工程师 Assistant engineer
26．验船师（机）Register
27．验船师（船）Surveyor
28．油漆工 Painter
29．焊工 Welder
30．大橱 Chief cook
31．物料员 Store keeper
32．加油工 Oiler
33．机工 Mechanic
34．甲板员 Deck man
35．电线工 Wireman
36．外包工 Laborer
37．铸工 Molder
38．管子工 Pipe fitter
39．起重工 Crane operator
二、柴油机类(Words about diesel engine)
1．主机 Main engine
2．二冲程柴油机 Two-stroke diesel engine
3．四冲程柴油机 Fore-stroke diesel engine
4．高速柴油机 High speed diesel engine
5．中速柴油机 Middle speed diesel engine
6．低速柴油机 Low speed diesel engine
7．气缸盖(缸头) Cylinder head
8．安全阀 Safety valve
9．释放阀 Relief valve
10．示功阀 Indicator valve
11．示功考克 Indicator cock
12．空气起动阀 Air starting valve
13．起动空气分配器 Air starting distributor
14．油头(燃油喷射器) Fuel injector
15．排气阀 Exhaust valve
16．气缸套 Cylinder liner
17．冷却水套 Cooling water jacket
18．气缸注油器 Cylinder lubricator
19．活塞 Piston
20．活塞头 Piston crown
21．活塞裙 Piston skirt
22．活塞销 Piston gudgeon pin
24．活塞杆 Piston rod
25．活塞环 Piston ring
26．活塞环槽 Piston ring groove
27．压缩环 (气环) Compression ring
28．刮油环 (油环) Oil scraper ring
29．减磨令 Wear ring (copper ring)
30．伸缩管(水拉管) Telescopic pipe
31．活塞冷却空间 Piston cooling space
32．填料箱(函) Stuffing box
33．填料箱密封环Sealing ring for Stuffing box
34．填料箱压缩环 Pressure ring for Stuffing box
35．填料箱刮油环Scraper ring for Stuffing box
36．扫气箱 Scavenging receiver
37．扫气口 Scavenging port
38．排气口 Exhaust port
39．十字头 Cross head
40．十字头销 Crosshead pin
41．十字头轴承 Crosshead bearing
42．十字头滑块 Crosshead slipper
43．滑块 Guide shoe
44．十字头导板 Crosshead guide plate
45．连杆 Connecting rod
46．连杆大端轴承 Bid end bearing
47．连杆小端轴承 Small end bearing
48．曲柄轴承 Crank bearing
49．曲柄销 Crank pin
50．曲轴 Crank shaft
51．曲轴颈 Crank journal
52．曲柄臂 Crank web
53．拐档差 Crank deflection
54．主轴承 Main bearing
55．主轴颈 Main journal
56．轴承瓦 Bearing bush
57．上轴瓦 Upper bearing bush
58．上轴瓦 Upper half
59．下轴瓦 Lower bearing bush
60．下轴瓦 Lower half
61．推力轴承 Thrust bearing
62．推力块 Thrust pad
63．推力盘 Thrust disc
64．推力轴 Thrust shaft
65．底座 Bed plate
66．机架 Frame
67．曲柄箱 Crank case
68．曲柄箱导门 Crank case door
69．曲柄箱防爆门 Explosion-proof Crank case.
70．定时齿轮 Timing gear
71．飞轮 Flying wheel
72．凸轮 Cam
73．凸轮轴 Cam shaft
74．喷油凸轮 Fuel injection cam
75．链条 Chain
76．链条轮 Chain wheel
77．链条箱 Chain box
78．推杆 Push rod
79．摇臂 Rocker arm
80．排气阀 Exhaust valve
81．吸气阀 Suction valve
82．排气总管 Exhaust manifold
83．进气总管 Air inlet manifold
84．高压燃油管 High pressure fuel pipe
85．活塞冷却水管 Piston cooling water pipe
86．法兰 Flange
87．贯穿螺栓 Tie bolt (tie rod)
88．端盖 Side cover
89．滑油泵 Lubricating oil pump
90．燃油泵 Fuel oil pump
91．滑油泵齿轮 Gear for lubricating oil pump
92．燃油泵齿轮 Gear for fuel oil pump
93．叶轮 Impeller
94．柱塞 Plunger
95．导杆 Guide rod
96．导套 Sleeve
97．滚动轴承 Ball bearing
98．滑动轴承 Sliding bearing
99．推力滚动轴承Thrust ball bearing
100．推力面 Thrust surface (thrust side)
101．盘车机 Turning gear
102．增压器 Turbocharger
103．涡轮机(透平) Turbine
104．涡轮 Turbine wheel
105．涡轮叶片 Turbine blade
106．喷嘴 Nozzle
107．废气叶轮 Exhaust impeller
108．废气叶轮片 Exhaust blade
109．废气端 Exhaust side
110．透平端 Turbine side
111．转子轴 Rotor shaft
112．油泵 L.O.pump
113．换向装置 Reversing device
114．换向伺服期 Reversing servomotor
115．压气机(鼓风机) Blower
116．膨胀接 Expansion joint
117．调速器 governor
118．飞重 Flying weight
119．补偿阀 Compensate valve
120．针阀 Needle valve
121．开口销 Cotter pin
122．轴封 Shaft seal
123．机械密封 Machinery seal
124．配电盘 Switchboard
125．应急配电盘 Emergency switchboard
126．应急发电机 Emergency generator
127．滤器 Filter
128．细滤器 Filter
129．粗滤器 Strainer
130．滑油滤器 L.O. filter
131．燃油滤器 F.O. filter
132．空气消音器 Air intake silencer
132．空气滤器 Air intake filter
133．空气瓶 Air bottle (receiver)
134．分油机 Separator
135．油水分离器 Water-oil separator
136．净油机 Purifier
137．燃油净化器 F.O. purifier
138．二氧化碳 CO2
139．二氧化碳瓶 CO2 bottle
140．正时齿轮 Timing gear
141．导向棒装置 Guide bar
142．注油器驱动 Lubricator driver
143．链条张紧装置 Chain tightener
144．凸轮轴传动轮 Chain wheel on cam shaft
145．中间链链传动轮Intermediate chain wheel
146．注油器驱动装置Lubricator drive
147．链条张紧装置 Chain tightener
148．滚筒导座 Roller guide housing
149．应急操纵台 Emergency console
150．力矩平衡器 Moment compensator
151．主启动阀 Main starting valve
152．启动空气分配器Starting air distributor
153．喷油器 Fuel valve
154．扫气系统 Scavenge air system
155．安全帽 Safety cap
156．机座 Bed plate
157．轴向振动减振器 Axial vibration damper
158．贯穿螺栓 Arrangement of stay bolt
159．示功器驱动装置 Indicator driver
160．端罩 End shields
161．气缸架 Cylinder frame
162．气阀传动装置 Valve operating device
163．摇臂润滑油泵 Rocker arm lubricating oil pump
164．摇臂润滑油柜 Rocker arm lubricating tank
165．摇臂润滑滤器Rocker arm lubricating filter
三、船舶机械类(Words about marine machinery)
1．船用锅炉 Marine boiler
2．废气锅炉 Exhaust boiler
3．辅锅炉 Donkey boiler
4．组合式锅炉 Combined boiler
5．火管 Fire tube
6．给水管 Feed pipe
7．炉膛 Furnace
8．炉墙 Furnace wall
9．火侧 Fire side
10．水侧 Water side
11．燃烧器 Oil burner
12．安全阀 Safety valve
13．上排污 Upper drain
14．下排污 Lower drain
15．锅炉皮阀 Mounting valve
16．水位计 Water level gauge
17．压力表 Pressure gauge
18．主汽门 Main steam valve
19．玻璃管 Glass tube
20．空调装置 Air-conditioning plant
21．制冷装置 Refrigerating plant
22．冰机 Fridge. Machine
23．空气压缩机 Air compressor
24．造水机 Fresh water generator
25．板式冷却器 Plate type cooler
26．机舱天车 Engine room crane
27．天车导轨 Crane rail
28．电磁阀 Solenoid valve
29．舵机 Steering gear
30．舵承 Rudder bearing carrier
31．液压缸 Hydraulic cylinder
32．废气涡轮增压器Exhaust gas turbocharger
33．弹簧阀 Spring loaded valve
34．冷凝器 Condenser
35．分油器 Oil separator
36．轴带发电机 Shaft generator
37．焚烧炉 Oil burner
38．分油机 Separator
39．分离筒 Separator bowl
40．配水盘装置 Paring disc device
41．转数计 Revolution counter
42．控制阀 Control valve
43．辅机 Auxiliary machinery
44．制冷装置 Refrigerating plant
45．海水淡化装置Sea water desalting plant
46．热交换器 Heat exchanger
47．船用气瓶 Marine air bottle
48．冷风机 Cooler unit
49．防水风门 Fire damper
50．气密挡板 Gas tight damper
51．排气风机 Exhaust fan
52．舱室通风机 Cabin fan
53．机舱通风机 Engine room fan
54．应急鼓风机 Emergency blower
四、阀门(Words about valve)
1．吸气阀 Suction valve
2．排气阀 Exhaust valve
3．控制阀 Control valve
4．导 阀 Pilot valve
5．单向阀 Non-return valve
6．口琴阀 Flap valve
7．调节阀 Regulating valve
8．液压阀 Hydraulic valve
9．膨胀阀 Expansion valve
10．给水阀 Feed valve
11．排水阀 Discharge valve
12．截止阀 Stop valve
13．吹泄阀 Blow-off valve
14．空气阀 Air valve
15．泄放阀 Drain valve
16．止回阀 Check valve
17．海底阀 Sea valve
18．回流阀 Retune valve
19．节流阀 Throttle valve
20．进气阀 Inlet valve
21．出气阀 Outlet valve
22．热力阀 Thermal valve
23．中央阀 Center valve
24．单向阀 One way valve
25．二通阀 Two way valve
26．三通阀 Triple valve
27．旁通阀 By-pass valve
28．换向阀 Change-over valve
29．减压阀 Pressure-recing valve
30．溢流阀 Overflow valve
31．自闭阀 Self-locking valve
32．针阀 Needle valve
33．平衡阀 Balance valve
34．循环阀 Circulation valve
35．主 阀 Main valve
36．滑 阀 Slide valve
37．蝶 阀 Butter-fly valve
38．截止阀 Shut-off valve
39．闸板阀 Gate valve
40．通海阀 Sea suction valve
41．吹除阀 Sea chest cleaning valve
42．防浪阀 Storm valve
43．舱壁阀 Bulkhead valve
44．快关阀 Emergency shut off valve
45．呼吸阀 Breather valve
五、泵类(Words about pump)
1．电动泵 Motor-driven pump
2．柱塞泵 Plunger pump
3．叶片泵 Vane pump
4．回转泵 Rotary pump
5．齿轮泵 Gear pump
6．往复泵 Reciprocating pump
7．离心泵 Centrifugal pump
1．电动泵 Motor-driven pump
2．柱塞泵 Plunger pump
3．叶片泵 Vane pump
4．回转泵 Rotary pump
5．齿轮泵 Gear pump
6．往复泵 Reciprocating pump
7．离心泵 Centrifugal pump
8．真空泵 Vacuum pump
9．螺杆泵 Screw pump
10．喷射泵 Ejector pump
11．冷却泵 Cooling pump
12．淡水泵 Fresh water pump
13．海水泵 Sea water pump
14．给水泵 Feed water pump
15．循环泵 Circulating pump
16．锅炉给水泵 Boiler feed pump
17．卫生水泵 Sanitary pump
18．压载泵 Ballast pump
19．舱底泵 Bilge pump
20．污水泵 Sewage pump
21．燃油泵 Fuel pump
22．高压油泵 High pressure pump
23．底压油泵 Low pressure pump
24．驳运泵 Transfer pump
25．增压泵 Booster pump
26．消防泵 Fire pump
27．通用泵 G.S. pump
28．旋涡泵 Regenerative
29．蜗壳泵 Volute pump
30．导叶泵 Diffuser pump
31．单联泵 Simplex pump
32．双联泵 Duplex pump
33．多联泵 Multiplex pump
34．活塞泵 Piston pump
35．减摇泵 Anti-roll pump
36．总用泵 General service pump
37．应急消防泵Emergency fire pump
38．扫舱泵 Stripping pump
39．货油泵 Cargo oil pump
40．滑油泵 Lubricating oil pump
六、甲板机械类（Deck machinery）
1．锚机 Windlass
2．锚机轴 Windlass shaft
3．刹车带 Brake lining
4．离合器 Clutch
5．锚链轮 Anchor Chain wheel
6．轴承瓦 Bearing bush
7．轴承盖 Bearing cover
8．绞揽机 Capstan
9．系揽绞车 Mooring winch
10．卷缆车 Reel
11．钢丝绳 Wire rope
12．卡环 Shackle
13．缆绳 Mooring rope
14．滑轮 Block
15．刹车装置 Brake device
输入内容已经达到长度限制