duplex在阀门里是什么意思呢

『壹』 求助英文高手 知道阀门的 帮忙翻译一下

10关闭3 / 4“超级双闸板阀800级螺栓阀盖OS&Y a182-f60 2205双工硬面座椅NACE MR0175

• super超级的，极度的，过分的，超等的，极好的; 面积的，平方的; 特级品，特大号商品; 非常，过分地; 用上浆纱布装; 担任跑龙套角色
• plex有两部分的; 连栋式的两栋住宅; 联式房屋; 占两层楼的公寓套房; 复式住宅
• gate门; 闸门; 登机门; 入场费; 给…装大门; 电波传送
• valves阀( valve的名词复数 ); 真空管; 活栓; 瓣膜
• class班; 阶级; 等级; 种类; 把…归入某等级，把…看作; 把…编入某一班级; 很好的，优秀的，出色的; 属于…类，被列为某类
• bolted bonnet螺栓连接阀盖，螺栓压盖
• hard硬的; 困难的; 有力的; 努力的; 努力地; 猛力地; 严重地; 沉重地; 英〉硬海滩，登陆处
• faced具有…脸型的; 有…表面的; 有…贴边的; 饰面的; 面对( face的过去式和过去分词 ); 面向…; 正视; 承认
• seats席位( seat的名词复数 ); 中心; 所在地; 有…座位的; 使就座( seat的第三人称单数 ); 使就职; 使获得座位; 可容纳若干座位
• naceNational Advisory Committee on Electronics <美，印>国家电子顾问委员会

『贰』 在路由器里以太网口配置 plex auto speed auto是什么意思

plex auto 是双工的协商模式为自动
双工模式有两种，一种是full（全双工），一种是half（半双工）
speed auto 是速率为协商模式为自动
一般的100M口支持: 10M，100M和自动模式

选择为自动模式则接口会和对端设备的接口进行协商，并自动选择最佳模式。

『叁』 本地连接中属性配置里的speed&plex是指什么

因为这个是在交换机里设置的，speed是端口的速率
可调为10m
100m
1000m（如果你交换机是千兆的话），plex是双工模式。一般这两个是不用调的，自适应就行，这是控制不了流量的。

『肆』 交换机里设置flow control（on/off)有什么用设置了speed&plex里的speed之后还需设置流量控制吗谢谢

flow control（on/off) 这个是流控开关.在网络发生阻塞的情况下才用的上,阻塞发生后像对端设备发送报文,对方设备将减少发送报文速率。

speed&plex 这是端口的速率，可调为10M、100M、1000M（如果你交换机是千兆的话）plex是双工模式。一般这两个是不用调的，自适应就行。

在设置了speed之后还需要设置流量控制，也是就设置交换机的flow control（on/off)为on。

(4)plex在阀门里是什么意思呢扩展阅读

Flow Control一概念起源于网络通信中。PCIe总线采用Flow Control的目的是，保证发送端的PCIe设备永远不会发送接收端的PCIe设备不能接收的TLP（事务层包）。也就是说，发送端在发送前可以通过Flow Control机制知道接收端能否接收即将发送的TLP。

在PCI总线中，并没有Flow Control这样的机制，因此发送端并不知道当前时刻，接收端能够接收对应的TLP。因此，发送端只能先尝试发送，期间可能会被插入多个等待周期（接收设备尚未就绪等原因），甚至是重发（Retries）等。

PCIe Spec规定，PCIe设备的每一个端口（Ports）都必须支持Flow Control机制，在发送TLP之前，Flow Control必须先检查接收端口是否有足够的Buffer空间来接收这个TLP。当PCIe设备支持多个VC（Virtual Channel）时，Flow Control机制可以显著地提高总线的传输效率。

『伍』 弯通球、刀型耐磨浆液阀、链轮刀型耐磨浆液阀、超短型球阀、圆刀式浆液阀都怎么翻译呢

实在是太多了，你有些专业的东西我又不懂，自己找找，拼凑一下
abdominal valve
腹瓣(雄蝉)
absorber valve
【信】吸收电子管
adjusting valve
调整阀, 调节阀
admission valve
进气阀; 进浆阀
agitating valve
搅拌桨
air valve
(空)气阀
air admission valve
进气阀
air bleed(ing) valve
排气阀; 排气嘴
air control valve
空调阀
air cylinder valve
气筒阀
air escape valve
泄气阀
air inlet valve (=air intake valve)
进气阀; 进风阀
air pilot valve
空气导向阀
air pressure governor valve
风压调压阀
air relay valve
空气中继阀
air release valve (=air relief valve)
排气阀; 放空阀
air reversing valve
空气换向阀
air shut-off valve
空气关闭阀
air signal recing valve
空气信号减压阀
air slide valve
空气分配阀
air starting (control) valve
空气起动(控制)阀
air straining check valve
空气滤尘止回阀
air vent valve
气动调压阀, 排气阀
air-actuated direction valve
气动控制换向阀
air-compressor valve
空气压缩机阀门
air-operated valve
气动阀
air-operated reversing valve
气动换向阀
air-vacuum change-over valve
空真转换阀
air-vacuum proportional valve
空真比例阀
air-vacuum two way valve
空真二位阀
alarm valve
报警阀
aligned grid valve
栅极中点校直的电子管
aligned grid tube
栅极中点校直的电子管
Allan valve
阿伦滑阀
altitude valve
【航空】高度阀(航空发动机汽化器的可调整阀)
ammonia valve
【工】氨阀
amplifying valve (=amplifier valve)
放大(电子)管
angle valve
角阀
angle back-pressure valve
背压角阀
angle globe valve
折角球形阀
angle stop valve
弯形止阀, 折角止阀
angle water valve
折角水阀
annular ring valve
环形阀; 环状阀
anti-g valve
【航空】防超重活门, 抗重力阀
antisurge valve
【航空】防喘振活门
application valve
作用阀, 控制阀
application pilot valve
作用导阀
ashpan blower valve
灰盘吹风阀
Askania valve
射流管阀
atmos valve (=atmospheric valve)
大气阀, 空气阀; 放空阀
atrio-ventricular valve
房室瓣
auricular valve
心耳瓣
auto tyre valve
汽车胎的汽门
autocontrol valve
自动控制阀
automatic valve
自动阀
automatic air valve
自动空气阀
automatic brake valve
自动制动阀
automatic control valve
自动控制阀
automatic cutout valve
自动切断阀门
automatic delivery control valve
自动输送控制阀
automatic drain valve
自动排水阀
automatic expansion valve
(定压式)自动膨胀阀
automatic gas sampling valve
自动气体进样阀
automatic recing valve
自动减压阀(高速制动机)
automatic regulating valve
自动调节阀
automatic spring loaded valve
自动弹簧阀
automatic supplementary air valve
自动补充(空)气阀
automatic unloading valve
自动卸载阀
automatic water level valve
自动水准阀
automatically operated valve
自动操作阀
automatic-control servo valve
自动控制伺服阀
auxiliary valve
辅助阀(暖汽调整阀用)
auxiliary changeover valve
辅助切换阀
back valve
回动阀, 止回阀, 逆止阀, 单向阀
backflush valve
反冲阀
backlash valve
无游隙阀门
back-pressure valve
止回阀
back-up valve
列车后端制动阀
balance valve
平衡阀, 均压阀
balance pressure recing valve
平衡减压阀
balance slide valve
平衡滑阀
balanced distribution valve
平衡配气阀
balanced safety valve
平衡式安全阀(可变动背压)
ball valve
球阀, 弹子阀
ball check valve
止回球阀, 球形节流阀
ball float valve
浮子阀, 浮球阀
ball non-return valve
球形止回阀
ball relief valve
球形安全阀
ball safety valve
球形安全阀
ball stop valve
球形止阀
ball-and-lever valve
杠杆球阀
battery valve
电池供电管, 直流管
beam deflection valve
电子束偏转管
射束偏转管
beam-power valve
电子束功率管
bell valve
钟形阀, 装料钟
bellows valve
波纹管阀
bellows-operated pilot valve
膜盒控制导阀, 膜盒导引阀
bevel seat valve
斜座阀, 角阀
biased valve
承载阀
bicuspid valve
二尖瓣
bigrid valve
双栅管
blast furnace gas valve
高炉煤气阀
blast regulation valve
通风调节阀
bleed valve
排出阀; 放泄阀
bleeder valve
放液阀, 放水阀
block valve
隔断阀
blocking valve
闭塞阀
blow valve
通风阀, 安全阀, 放空阀
blow-down valve
排气阀
blower valve
鼓风机阀
blower drain valve
鼓风机放泄阀
blower regulation valve
通风调节阀
blow-off valve
排出[泄]阀, 放泄[空]阀, 喷放阀
blowout valve
排气管, 排出阀
boiler check valve
锅炉止回阀
boiler feed valve
锅炉给水阀
bonnet valve
帽状阀
bottom valve
底阀
bottom drain valve
底部放泄阀
brachial valve
腕瓣
brake valve
制动阀
brake application valve
制动作用阀
brake application magnet valve
电磁制动阀
brake control valve
制动控制阀
brake cylinder release valve
制动缸缓解阀, 制动缸放风阀
brake metering valve
制动调节阀
brake pipe compensating valve
制动管补偿阀
brake release magnet valve
缓解电磁阀
brake-field valve
正栅管
brass valve
黄铜阀
brass-fitted cast-iron valve
黄铜配制铸铁阀
brass-trimmed valve
黄铜配制阀
breather valve
通气阀, 呼吸阀
breathing valve
呼吸瓣
breathing type safety valve
呼吸式安全阀(罐车)
bright emitter valve
白炽灯丝电子管, 钨丝电子管
brine retaining valve
盐水箱保持阀
bucket valve
活塞阀
buffer change valve
缓变阀
building block valve
积木式阀, 集成阀
built-in check valve
内装式单向阀
bullet valve
球阀
buried valve with key
液下控制阀
butterfly valve
蝶形阀
butterfly control valve
蝶形控制阀
butterfly throttle valve
蝶形节流阀
by-pass valve
旁通阀, 辅助阀, 回流阀
by-path valve
旁通阀, 辅助阀, 回流阀
cab turret valve
蒸汽塔总汽门
caboose valve
守车阀
cage type valve
笼形阀
cam-operated valve
凸轮控制阀
capless tyre valve
无帽胎阀
car discharge valve
车辆放风阀
car signal valve
车辆信号阀, 车辆放风阀
cardiac valve
【解】贲门瓣
cartridge inserted valve
筒式插装式阀, 插装阀
cement valve
【机】水泥止回阀
center valve
中心阀
centre bypass valve
中间位置旁通的换向阀, M型机能换向阀
centre spool valve
中心柱形阀
centrifugal saw plate valve
离心机的圆盘保险(溢流)阀
centrifugal type injection valve
离心式喷射阀
change valve
换向阀, 三通阀
changeover valve
活页阀
旋转阀, 转换阀
多向阀
charge valve
充气阀, 加载阀, 加液阀
charging valve
充气阀, 加载阀, 加液阀
charging check valve
充气止回阀
check valve
单向阀, 止回阀, 防逆阀
检验阀
chimney valve
烟道阀
choke valve
阻风门
choker checkvalve
阻气单向阀
cindervalve
卸灰阀
Cineston controller brake valve
钦式控制制动联合阀 (用于地下铁道)
circulating-water valve
循环水阀
circulation valve
环流阀
clack valve
止回阀
clapper valve
瓣阀
clock valve
单向绞链阀
closed center valve
中间位置封闭的阀(方向阀); 闭中心阀
closed crossover valve
正遮盖的换向阀
closed exhaust valve
密闭排气阀
closed-type fuel valve
密闭形燃油阀
closing valve
隔离阀, 节制阀, 隔断阀, 停汽阀
clutch application valve
离合器作用阀
clutch temperature adjusting valve
离合器温度调节阀
coasting valve
滑行阀, 惯性运动阀
coaxial valve
同轴管[阀]
cold water stop valve
凉水止阀
column valve
柱阀
column shut-off valve
柱关闭阀
column switching valve
柱转换阀
combination valve
组合阀
combination sliding and rotary spool valve
又移动又旋转的圆柱滑阀
combined inlet-outlet valve
进出组合阀
combined reheat (stop and intercept) valve
再热联合汽门, 中压联合汽门
combined strainer and check valve
混合滤尘止回阀
common slide valve
普通滑阀
compensated flow control valve
带压力补偿的流量控制阀
调速阀
compensated relief valve
平衡式溢流阀
compensating valve
补偿阀
compensating air valve
补充空气阀, 补偿气阀, 平衡气阀
compensation valve
平衡阀, 补偿阀
compression valve
(减振器的)压缩行程阀
compression release valve
减压阀
compressor valve
压气机气门
concentric valve
同心阀
condensate valve
凝结水阀
condenser valve
凝汽阀
condenser level control valve
凝汽器水位调节阀
condenser relief valve
凝气器安全阀
conctor's valve
车长阀, 紧急制动阀
cone valve
锥形阀
cone-way valve
单向阀
conical valve
锥形阀
conical seat valve
锥形座阀
constant pressure valve
恒压阀
constant pressure expansion valve
恒压膨胀活门, 恒压膨胀阀
control valve
控制阀, 调节阀
控制管, 调节管
control air valve
控制空气阀
control air type recing valve
控制空气型减压阀
controllable check valve
可控单向[止回检验]阀
controller pilot valve
控制器管制阀
conversion valve
转换阀
转向阀
convex head valve
凸形气门头
cooled type valve
冷却式真空管
cooling fan electro-pneumatic valve
冷却风扇电空阀
coplanar-grid valve
共面栅极管(具有两个控制栅的四极管)
ing valve
(仿形装置的) 仿形阀
corner valve
角阀
coronary valve
【解】冠状瓣
counterbalance valve
背压阀,反平衡阀
coupling valve
联结阀
coupled valve
联结阀
crab-pot valve
捕蟹器式阀
crack valve
瓣阀
cranked tire valve
轮胎气嘴
cross valve
转换阀, 三通阀
cross feed valve
双向进给阀
crossover valve
交换阀, 转换阀
crossover gasoline valve
重叠的汽油阀
crystal valve
晶体管
cup valve
杯形阀, 钟形阀
cured-in valve
硫化在内胎里的气嘴[孔]
current regulating valve
电流调节阀
cushion valve
缓冲阀, 弹性阀, 减震阀
cushioned channel valve
气垫槽阀
cut slide valve
膨胀滑阀
cut-in valve
接入阀
cut-off valve
截止阀, 逆止阀
cut-off slide valve
断流滑阀
cut-out magnetic valve
截断电磁阀
cycle tube valve
循环管阀
cycling valve
循环阀(安全制动)
cycling solenoid valve
周期(工作的)电磁阀
cylinder valve
气缸阀
cylinder bypass valve
汽缸旁通阀
cylinder cock valve
汽缸排水操纵阀
cylinder drain valve
汽缸自动排水阀
cylinder relief valve
汽缸安全阀
cylinder test valve
汽缸(积水)试验阀
cylindrical valve
柱形阀
cylindrically balanced valve
柱形平衡阀
damping valve
阻尼阀;阻尼管
dark-tint valve
深色彩色电视管
dead-weight safety valve
静载荷保安阀
deck valve
台阀
decompression check valve
卸压单向阀
deflation valve
放气阀
deflection valve
射束偏转管
delivery valve
导出阀; 排气阀; 出油阀
delivery check valve
送油节止阀
density control valve
调浓阀; 浓度控制阀
deriming valve
解冻阀
detecting valve
检波管
detector valve
检波管
diaphragm valve
膜板阀, 隔膜阀; 针阀, 给水调整阀
diaphragm control valve
膜片控制阀
diaphragm cut-off valve
膜板截断阀
differential valve
差动阀
differential pressure fuel valve
压差油阀
differential pressure regulating valve
差压调节阀
differential relay valve
差动中继阀
differential sliding valve
差动滑阀
diffuser valve
扩散阀
diffusing type steam valve
扩压式汽阀
direct admission valve
直接进风阀
direct pressure control valve
直动式压力控制阀
direct-acting valve
直动阀
direct-acting control valve
直接作用控制阀
direct-acting solenoid valve
直接动作螺管阀
direct-mounted valve
管式连接阀
direction(al) control valve
方向控制阀
director valve
主导活门
disc valve
片状阀
discharge valve
排出阀;卸料阀
disconnecting valve
断流阀, 断开阀, 截止阀
disc-type recing valve
盘式减压阀
diskvalve
盘形阀
distributing valve
分配阀
distributing slide valve
分配滑阀
distribution valve
分配阀
diverter valve
偏向型元件
分流阀
dividing valve
分流阀
dividing control valve
分配控制阀
dorsal valve
【解】背瓣
double valves
双阀
double branch stop valve
双向止流阀
double check valve
双止回阀, 双单向阀
double damper valve
双调节阀, 双减振阀
double gate valve
双闸阀
double ported valve
双口阀
double pressure feed valve
双压进给阀
double return valve
双止回阀, 双回流阀
double safety valve
双安全阀
double seat balanced valve
双座平衡阀
double seated main stop valve
双座式主汽门
double sleeve valve
双套阀
double slide valve
双动滑阀
double-anode valve
双屏极电子管
double-beat (drop) valve
双座阀, 双支承提升阀, 平衡阀
double-beat poppet valve
双层提升阀
double-face valve
双面阀
double-faced slide gate valve
两面滑门阀
double-grid valve
双栅管
double-heading valve
重联阀
double-piston valve
双活塞阀
double-ported slide valve
双动滑阀
double-purpose valve
【电子】双作用管
double-ring valve
双环阀
double-triode valve
双三极管
drain valve
排水阀;泄水阀
draw-off valve
排水阀;泄水阀
drip valve
排水阀;泄水阀
driver's automatic brake valve
司机自动制动阀
driver's vacuum brake valve
司机真空制动阀
drop valve
落阀
dropping valve
降压阀, 减压阀
drum valve
鼓形阀
al ball check valve
双球止逆阀
al-gravity valve
【化工】双比重阀
mp valve
倾泄阀(安全阀)
Duner flush valve
达式水阀
plex check valve
双止回阀
plex release valve
复式缓解阀
dynamic valve
动力阀
dynamic brake blending valve
动力制动混合阀
eccentric valve
偏心阀
effluent sample valve
试样流出阀
Eidophor light valve
艾多福光阀(电视投影机)
electric valve
整流管
electric control valve
电动调节阀
electric pneumatic valve
电空阀
electrically operated valve
电动阀
electrochemical valve
电解阀
electrohydraulic valve
电-液阀
electromagnetic valve
电磁阀
electromagnetic gas valve
电磁气阀
electromagnetic light valve
电磁(控制)光阀
electrometer valve
静电计电子管
electron valve
电子管
electronic valve
电子管
electrooptic light valve
电光光阀
electropneumatic valve
电动气动阀, 电磁气阀
electropneumatic carretarder valve
车辆减速器的电空阀, 车辆缓行器的电空阀
electropneumatic distributing valve
电动气动分配阀
electropneumatic signal valve
信号机电动气动阀
electro-pneumatic switch valve
转辙机电动气动阀
electropneumatic train stop valve
列车自动停车电动气动阀
emergency valve
安全阀
紧急阀
emergency application valve
紧急作用阀
emergency brake valve
紧急制动阀, 车长阀
emergency breakaway valve
紧急断气阀
emergency closing valve
应急阀
emergency pressure increasing valve
紧急增压阀
emergency pressure recing valve
紧急减压阀
emergency relay valve
紧急继动阀
emergency stop valve
危急遮断阀, 紧急止流阀, 主汽门
emergency trip valve
危急遮断阀, 紧急止流阀, 主汽门
emergency trip magnet valve
紧急脱钩电磁阀
emergency vent valve
紧急放风阀
empty and load valve
空重车转换阀
empty wagon safety valve
空车安全阀
emptying valve
泄空阀, 排油阀
end valve
尾阀
end train-pipe valve
暖气管端阀
engine valve
发动机阀, 发动机[汽缸]气门
engine brake valve
机车制动阀
engine compartment drain valve
(发动)机舱放泄阀
engine stop valve
停车阀
engine thermostat housing drain valve
发动机恒温器壳放泄阀
engineer's brake valve
司机制动阀
equalizing valve
平衡阀, 均匀阀, 减压阀
equalizing discharge valve
均衡放风阀
equalizing graating valve
均衡递动阀
equalizing piston valve
均衡鞲鞴阀
equalizing slide valve
均衡滑阀
equilibrated valve
预启阀, 压力平衡阀
equilibrium valve
平衡阀
equilibrium slide valve
平衡滑阀, 放泄滑阀
equivalent valve
等效电子管
escape valve
排气阀, 安全阀
eustachian valve
【解】腔静脉瓣, 欧氏瓣
excess flow valve
流量限制阀
excess pressure valve
过压阀
exhalation valve
吸气阀
exhaust valve
排气阀, 排气门
exhaust by-pass valve
排气旁通阀
exhaust manifold heat valve
排气歧管加热阀
exhaust steam valve
排汽阀
exhauster regulating valve
真空泵调节阀
expansion valve
膨胀阀; 安全阀
expansion valve with pilot valve
导向式自动膨胀阀
expansion relief valve
膨胀安全阀
explosion relief valve
防爆安全阀, 安全阀
explosive valve
爆发活门
extra-air valve
辅助气阀(附加空气阀)
extraction valve
抽汽阀
extraction check valve
抽汽逆止阀
extraction control valve
抽气调节阀
extraction regulating valve
抽气调节阀
extraction stop valve
抽汽截止阀
face valve
座阀
fast valve
高速阀, 快关阀
feather valve
放气阀, 卸载阀, 滑阀
feed valve
进给阀, 喂阀; 给气阀; 进水阀
feed check valve
给水止回阀
feed stop valve
进给安全阀
feed-control valve
进给控制阀
feed-regulating valve
进给调节阀, 给水调整阀
fermentation valve
发酵阀
field weakening valve
削弱磁场阀
field-strengthening valve
磁场加强阀
filling valve
进油阀
filling limit valve
充量限制阀
finger valve
(压缩机)单槽阀
fire valve
灭火阀, 消防阀
first amplifier valve
第一级放大管
fixed differential recing valve
定差减压阀
flange type everlasting blow-off valve
凸缘式连续放泄阀
flanged brass valve
凸缘铜阀
flap valve
片状阀;瓣阀
flapper valve
(喷嘴)挡板阀, 舌形阀
flat valve
平面座阀, 配流阀
flat seated valve
平座阀
flat slide valve
平滑阀
flat-operated relief valve
浮筒操纵安全阀
flexible tube valve
挠性管阀
float valve
浮阀, 回压阀
float control(led) valve (=float controller valve)
浮子(控制)阀, 液面调节阀
float needle valve
浮针阀
float-operated relief valve
浮球控制安全阀
float-switch controlled rotary-spool valve
浮动开关控制的旋转滑阀
flood(ing) valve
溢流阀
flop valve
瓣阀
flow valve
流量开关
flow diversion valve
液流转向阀
flow metering valve
流量控制阀
flow regulating valve
节流阀, 减压阀
flow-control valve
流量控制阀
fluid pressure recing valve
液压降低阀
fluid-control(led) valve
流体控制阀, 液力控制阀
flushing valve
冲洗阀
flush-out valve
冲出阀
flutter valve
翼形阀
follower valve
随动阀
follow-up valve
随动阀
foot valve
脚踩阀;底阀
forcing valve
增压阀
four-electrode valve
四极管
four way plug valve
四通塞阀
four-way valve
四通阀
frame output valve
帧信号输出管
free discharge valve
自由泄流阀
free flow valve
易流阀
free spool valve
带浮动阀芯的滑阀
frost valve
防冻阀
fuel valve
燃油阀
fuel admission valve
燃料进入阀
fuel control valve
燃料控制阀
fuel injection valve
燃油喷射阀
fuel outlet valve
放油阀
fuel-tank selector valve
燃油箱分离阀
ga(u)ge cock valve
水位旋塞阀
gasvalve
排气阀
gas admittancevalve
进气阀
gas and gasoline threeway valve
煤气与汽油三通阀
gas bleed valve
泄气阀
gas charging valve
充气阀(蓄能器)
gas check valve
闭气阀
gas control valve
气体调节阀
gas escape valve
煤气放气阀
gas inlet valve
进气阀
gas linking valve
燃气连结阀
gas oil solenoid valve
气体油料螺管阀
gas outlet valve
出气阀
gas precharge valve
充气阀
gas sampling valve
气体进样阀
gas-engine inlet valve
煤气机进气阀
gas-filled valve
充气管
gas-filling valve
充气阀
gasoline valve
汽油门
gas-tank valve
汽油箱汽门
gate valve
闸式阀, 闸门阀
gate gurgle valve
泄油阀
gate turn valve
旋转炉门
genital valve
生殖瓣
gland sealing steam control valve
汽封蒸汽调节阀
glass valves
玻璃阀
globe valve
球心阀
stop valve
球心阀
globe body valve
球形阀
globe stop valve
球形截流阀
governing valve
调速阀, 调节阀
governor valve
调速阀, 调节阀
governor magnet valve
调速器磁铁阀
governor slide valve
调节器滑阀
governor solenoid valve
调速器螺管阀
graating valve
调节阀;节制阀; 阶段制动阀
greaseless valve
无脂密封阀
grid valve
栅型阀
gridironvalve
格子阀
grid-type extraction valve
栅型抽汽阀
groove control valve
槽式节流阀
group valve
组合阀, 阀组
grout valve
灌浆阀
guard's valve
车长阀, 紧急制动阀, 速动闸门, 事故阀, 停车开关
guard's van valve
守车制动阀
guide(ing) valve
导向阀
half ball valve
半球形阀
hand air valve
手控气阀
hand brake valve
手制动阀
hand by-pass valve
手动旁通阀
hand oiler valve
注油器手阀
hand-operated brake valve
手操纵制动阀
hand-operated direction valve
手动换向阀
hanging valve
吊阀
hard valve
高真空电子管, 硬性电子管
head valve
头阀
顶置阀
heat control valve
热控制阀, 加热控制阀
heat regulating valve
热调整阀
heart valve
【解】心(脏)瓣膜
heater shut-off valve
(火花塞)加热器断流阀
height control valve
高度控制阀
high power valve
大功率管
high pressure float valve
高压浮球阀
high side float valve
高压浮球阀
high-pressure expansion valve
高压膨胀阀
high-pressure safety valve
高压安全阀[瓣]
high-pressure slide valve
高压滑阀
high-speed needle valve
高速针阀
high-speed recing valve
高速减压阀
high-vacuum valve
高真空整流管
hinged valve
瓣阀
hoist cylinder oil relief valve
起重机油缸油压安全阀
hoist pump check valve
起重机油泵止回阀
hoist pump control valve
起重机油泵操纵阀
holding valve
闭锁阀, 止回阀, 单向阀
hollow-jet needle valve
空注针形阀
homogenizing valve
均质机高压阀
horizontal valve
水平阀
hose valve
水带阀门
hot water regulating valve
水温调整阀
hot water stop valve
热水止阀
hot-blast valve
热风阀
hot-cathode gas filled valve
闸流管
hot-water check valve
热水止回阀
hull valve
舷侧阀, 通海阀
hydrant valve
消防龙头阀
hydraulic valve
液压阀, 调水活门
hydraulic back pressure valve
水保险器(焊接)
hydraulic control valve
液压控制

『陆』 阀门smo and plex 是什么材质

smo and plex
SMO和双工
v
smo and plex
SMO和双工

『柒』 什么是超级奥氏体不锈钢

254SMO是一种奥氏体不锈钢。由于它的高含钼量，故具有极高的耐点腐蚀和耐缝隙腐蚀性能。这种牌号的不锈钢是为用于诸如海水等含有卤化物的环境中而研制和开发的。254SMO也具有良好的抗均匀腐蚀性。特别是在含卤化物的酸中，该钢要优于普通不锈钢。其C含<0.03%，因此叫纯奥氏体不锈钢（<0.01%又叫超级奥氏体不锈钢）。超级不锈钢是一种特种不锈钢，首先在化学成分上与普通不锈钢不同，是指含高镍，高铬，高钼的一种高合金不锈钢。其中比较著名的是含6%Mo的254SMo，这类钢具有非常好的耐局部腐蚀性能，在海水、充气、存在缝隙、低速冲刷条件下，有良好的抗点蚀性能（PI≥40）和较好的抗应力腐蚀性能，是Ni基合金和钛合金的代用材料。其次在耐高温或者耐腐蚀的性能上，具有更加优秀的耐高温或者耐腐蚀性能，是304不锈钢不可取代的。另外，从不锈钢的分类上，特殊不锈钢的金相组织是一种稳定的奥氏体金相组织。

『捌』 蒸汽截止阀的截止阀材质

我们所说的阀门的材质一般是指阀体，阀体，英文：valvebody.是阀门的最主要的部件，是指阀门的外表整体；根据压力等级有不同的机械制造方法。例如：铸造、锻造等。阀体的材质根据不同的工艺介质，选用不同的金属材料或者塑料材料。

蒸汽截止阀的阀体使用的材质非常广泛，结合蒸汽阀门的进口品牌美国威盾VTON的各种阀体材质的蒸汽截止阀，主要有：铸钢，不锈钢，铸铁，球墨铸铁，锻钢A105，铬钼钢，铬钼钒钢，我们来分析下各种截止阀的阀体所适应的场合。

2、A105锻钢材质截止阀

A105是一种低碳钢锻件，与20钢类似。采用锻造的阀体的截止阀，适用于高温、高压介质的管路或装置上开启和关闭高温水，蒸汽的流体，如火电厂、核电站，石油化工系统的高温、高压管路上。

二、不锈钢阀体的截止阀

不锈钢（Stainless Steel）是不锈耐酸钢的简称，耐空气、蒸汽、水等弱腐蚀介质或具有不锈性的钢种称为不锈钢；而将耐化学腐蚀介质（酸、碱、盐等化学浸蚀）腐蚀的钢种称为耐酸钢。由于两者在化学成分上的差异而使他们的耐蚀性不同，普通不锈钢一般不耐化学介质腐蚀，而耐酸钢则一般均具有不锈性。

不锈钢常用于截止阀阀体的有不锈钢304、316、304L、316L，双相钢，2520

1、304截止阀和316截止阀都属于18Cr-9Ni，是18-8型铬镍奥氏体不锈钢的典型代表， 316主要是降低Cr含量提高Ni含量并增加了Mo2%~3%。从而其抗腐蚀性能力要比304强，适合在化工，海水等环境下使用，316比304在高温环境下更耐腐蚀。所以在高温环境下，工程师一般都会选用316材料的零部件。

2、316L截止阀一般是用于卫生级食品厂，饮料厂，生物厂。

3、双相钢截止阀双相不锈钢（Duplex Stainless Steel）S32750（SAF2507,F53）、S31803（SAF2205,F51）、654SMO、RS-2、XM-19（Nitronic50）、S21800（Nitronic60）、20Mo-6（N08026）、F55（S32760）、F60（S32205）、17-7PH（SUS631）、17-4PH（SUS630）、309S、310S（2520）、347（S34700）、A4、C4、CN7MNS143等，指铁素体与奥氏体各约占50%，一般较少相的含量最少也需要达到30%的不锈钢。在含C较低的情况下，Cr含量在18%~28%，Ni含量在3%~10%。有些钢还含有Mo、Cu、Nb、Ti、N等合金元素。该类钢兼有奥氏体和铁素体不锈钢的特点，与铁素体相比，塑性、韧性更高，无室温脆性，耐晶间腐蚀性能和焊接性能均显著提高，同时还保持有铁素体不锈钢的475℃脆性以及导热系数高，具有超塑性等特点。与奥氏体不锈钢相比，强度高且耐晶间腐蚀和耐氯化物应力腐蚀有明显提高。双相不锈钢具有优良的耐孔蚀性能，也是一种节镍不锈钢

三、铬钼钢阀体材质截止阀

铬钼钢阀体材质与高温高压特性关联，阀体的材质有:WC6。最高工作压力1.6-32MPA(美标从150LB-2500LB，)。工作温度-20°C- 550°C，阀门口径从DN10-DN300。连接方式:法兰、丝口或焊接。应用领域：机械设备、化工设备、通用零部件、工业设备、制药设备、通用设备、石化设备、电力设备、治金粉末设备、采矿设备，市政、电子工业等。

四、铸铁阀体材质截止阀

铸铁材质截止阀一般分为灰铸铁截止阀和球墨铸铁截止阀

1、灰铸铁截止阀，含碳量较高（2.7％～4.0％），碳主要以片状石墨形态存在，断口呈灰色，简称灰铁。熔点低（1145～1250℃），凝固时收缩量小，抗压强度和硬度接近碳素钢，灰铸铁截止阀成本低，价格便宜，适用于一般性要求不高的场合。

2、球墨铸铁截止阀，将灰口铸铁铁水经球化处理后获得，析出的石墨呈球状，简称球铁。比普通灰口铸铁有较高强度、较好韧性和塑性。一般进口品牌的截止阀，比如美国威盾VTON品牌的采用球墨铸铁。

『玖』 谁能告诉我有关各种阀门的英语翻译！！！

你要的基本上都有了，各种阀的名称、部件，相关用语。
如果你要各种阀门的解释，到这里
http://valve-2000.nease.net/shuyu.htm

CQ螺纹球阀 CQ Thread Ball Valves
L形三通式 L-pattern three way
T形三通式 T-pattern three way
安全阀 Safety valve
暗杆闸阀 Inside screw nonrising stem type gate valve
百叶窗; 闸板 shutter
百叶窗式挡板 louver damper
摆阀式活塞泵 swing gate piston pump
保温式 Steam jacket type
报警阀 alarm valve
报警阀; 信号阀; 脉冲阀 sentinel valve
背压调节阀 back pressure regulating valve
背压率 Rate of back pressure
本体阀杆密封 body stem seal
波纹管阀 Bellows valves
波纹管密封阀 bellow sealed valve
波纹管密封式 Bellows seal type
波纹管平衡式安全阀 Bellows seal balance safety valve
波纹管式减压阀 Bellows recing valve
波纹管式减压阀 Bellows weal recing valve
薄膜 thin film
薄膜; 隔膜 diaphragm
薄膜式减压阀 Diaphragm recing valve
薄型闸阀 Thin Gate Valves
不封闭式 Unseal type
槽车球阀 Tank Lorry Ball Valves
颤振 Flutter
常闭式 Normally closed type
常开式 Normally open type
超低温阀门 Cryogenic valve
超高压阀门 Super high pressure valve
超过压力 Overpressure of a safety valve
衬胶隔膜阀 rubber lined diaphragm
衬胶截止阀 rubber lined globe valve
垂直板式蝶阀 Vertical disc type butterfly valve
磁耦合截止阀 Magnetic Co-operate Globe Valves
带补充载荷的安全阀 Supplementary loaded safety valve
带辅助装置的安全阀 Assisted safety valve
单阀碟双面平行密封闸阀 parallel single disk gate valve
单口排气阀 Single Opening Exhaust Valves
单向阀 Non-return Valve
单闸板 Single gate disc
单闸板平板闸阀 Single Disc Flat Gate Valves
弹簧薄膜式减压阀 Spring diaphragm recing valve
弹簧式安全阀 Direct spring loaded safety valve
弹簧座 Spring plate
弹性闸板 Flexible gate disc
当量计算排量 Equivalent calculated capacity
挡板 damper
导阀 Pilot valve
导向套 Valve guide disc guide
低温阀门 Sub-zero valve
低压阀门 Low pressure valve
底阀 bottom valve
底阀 Foot valve
电磁动装置 Eletro magnetic actuator
电磁阀 magnetic valve
电磁阀 solenoid valve
电磁－液动装置 Eletro magnetichydraulic actuator
电动阀 mortor operated valve
电动阀 motorized valve
电动截止阀 Electric Actuated Stop Valves
电动平行式双闸板闸板 Electric Double Disk Parallel Gate Valves
电动楔式闸阀 Electric Actuated Wedge Gate Valves
电动装置 Electric actuator
电－液动装置 Eletro hydraulic actuator
电液伺服阀 electro-hydraulic servovalve
调节弹簧 Regulation spring
调节阀 adjusting valve
调节阀 control valve
调节阀 regulating valve
调节螺套 Adjusting bolt Adjusting screw
调节圈 Adjusting ring
蝶板 Disc
蝶阀；瓣阀 butterfly valve
蝶阀；瓣阀；拍门；铰链阀 flap valve
蝶式缓冲止回阀 Butterfly Type Non-slam Check
蝶式止回阀 Butterfly swing check valve
定比减压阀 Proprutioning pressure recing valve
定差减压阀 Fixed differential recing valve
定值减压阀 Fixed pressure recing valve
动态特性 Dynamic characteristics
对焊连接阀 Buttwelding valves
对夹蝶板阀 Wafer plate valves
对夹式衬胶蝶阀 Wafer Type Butterfly Valves with Rubber Itning
对夹式阀门 Clamp valves
对夹式止回阀 Wafer Check Valves
额定排量 Certified capacity
额定排量系数 Derated coefficient of discharge
二通阀 Two-way valves
阀 valve
阀板 valve deck plate
阀板 valve plate
阀板式活塞泵 valve deck plate type piston pump
阀板式活塞泵 valve plate type piston pump
阀瓣 Disc
阀操纵杆 valve operating rod
阀痤槽 valve seat recess
阀挡 valve grid
阀挡 valve positioner
阀挡 valve stop
阀导杆 valve tail rod
阀导向器 valve guide
阀盖 bonnet
阀盖衬套 bonnet bush
阀盖垫片 bonnet gasket
阀杆 stem
阀杆 valve rod
阀杆 valve spindle
阀杆端部尺寸 Dimmension of valve stem end
阀杆环 stem ring
阀杆螺母 Yoke bushing Yoke nut
阀杆填料 stem packing
阀杆头部尺寸 Dimension of valve stem head
阀簧 valve spring
阀簧压板 valve spring plate
阀控水锤泵 valve-controlled hydraulic ram
阀框架 valve yoke
阀门 Valve
阀门传动装置 valve bandle set
阀门和管件 Valves and Fittings
阀门盘根 valve packing
阀门手柄 valve handle
阀盘 disc
阀盘 valve disc
阀片 Disc
阀球 valve ball
阀驱动臂 valve driving arm
阀驱动臂 valve motion arm
阀式活塞 valve type piston
阀式活塞 valve type bucket
阀室式活塞泵 valve box type piston pump
阀室式活塞泵（美） valve pot type piston pump
阀抬起装置 valve lifting device
阀体 body
阀体 valve body
阀箱 valve box
阀箱 valve cage
阀箱 valve chest
阀箱；阀限位器 valve guard
阀箱盖 cover for valve box
阀箱盖 valve box cover
阀箱式活塞泵（美） turret type piston pump
阀形活塞泵 valve type piston pump
阀座 Seat ring
阀座 valve carrier
阀座 valve seat(body seat)
阀座；阀盘 valve seat
阀座环 seat ring
阀座密封嵌条 sealing strip for valve seat
法兰 flange
法兰堵头 blind flange
法兰端 flange end
法兰接头 flange joint
法兰连接紧固件（双头螺栓和螺帽） flange bolting
法兰密封面，法兰面 flange facing
法兰面加工 flange facing finish
法兰球阀 Flange Ball Valves
翻板阀 Flap
反冲盘 Disc holder
反向作用式减压阀 Reverse acting recing valve
反向作用式减压阀 Reverse acting recing valve
放空阀 emptying valve
放气阀 air vent valve;vent valve
放气阀；排气阀 air evacuation valve
放泄阀 escape valve
分置阀室式活塞泵 separate valve box type piston pump
分置阀室式活塞泵（美） side pot type piston pump
封闭式 Seal type
浮动式球阀 Float ball valve
浮球 Ball float
浮球阀 Float Valve
浮球式疏水阀 Ball float steam trap
浮球式疏水阀 Free Float Type Steam Trap
浮桶 Bucket float
浮桶式疏水阀 Open bucket steam trap
辅助（副）阀 Auxiliary valves
负荷率 Rate of load condensate
附加背压力 Superimposed back pressure
复位弹簧 Returnning spring
杠杆式 Lever type
杠杆式安全阀 Lever and weight loaded safety valve
杠杆式减压阀 Lever recing valve
高温阀门 High temperature valve
高压阀门 High pressure valve
格兰密封 gland
隔离阀 isolating valve
隔膜 Diaphragm
隔膜阀 diaphragm valve
隔膜式控制阀 diaphragm operated comtrol valve
工作背压 Operating back pressure
工作温度 Operating temperature
工作温度 Working temperature
工作压差 Operting differential pressure
工作压力 Operating pressure
工作压力 Working pressure
公称通径 Nominal diameter
公称压力 Nominal pressure
固定式球阀 Fixed ball valve
关闭压力 Lockup pressure
关阀过冷度 Subcooled temperature of close valve
关阀温度 Closing valve temperature
管道安全阀 Piping Safety Valves
过冷度 Subcoold temperature
过流阀(或节流阀) Restrictor Valves
喉径 Throat diameter
滑阀 slide valve
滑阀式回转活塞泵 rotary piston pump with slide gate
滑阀型转子泵 eccentric rotary pump with sliding sleeve
环形阀 annular valve
环形阀 double beat valve
换向阀 selector valve
换向阀 shuttle valve
回转滑阀活塞泵 piston pump with rotary gate
回座压力 Re-seating pressure of a safety valve
活塞昵减压阀 Piston recing valve
活塞式阀 piston valve
活塞式阀；柱塞式阀 plunger valve
活塞式减压阀 Piston recing valve
减速阀 Deceleration valves
减压比 Pressure recing ratio
减压阀 pressure recing valve
浆液阀 Parallel Slide Valves
角阀 Angle Valve
角阀 isolation valve angle configuration
角式 Angie type
角式节流阀 Angle Throttle Valves
角式截止阀 Angle Stop valves
铰链阀；片状阀 flapper valve
节流阀 throttle valve
节流阀 choke valve
节流阀；节流 throttle
结构长度 Face-to-face dimension ;End-to-end dimension; Face-to-centre dimension
结构形式 Type of construction
截止阀 Globe valve
截止阀 Shut-off Valve
截止阀；关断阀 shut-off valve
截止式隔膜阀 Globe diaphragm valve
紧急切断阀 Emergeny Cut-off Valves
进气阀 air intake valve
进水阀；进口阀门 inlet valve
静态特性 Static characteristics
静态特性偏差 Static characteristics derivation
开阀过冷度 Subcooled temperature of open valve
开阀温度 Opening valve temperature
开启高度 Lift
壳体试验 Shell test
壳体试验压力 Seal test pressure
空气阀门 Air valves
快速排污阀 Quick Draining Valves
类型 Type
冷凝结水排量 Cold condensate capacity
冷态试验差压力 Cold differential test pressure
理论排量 Theoretical flowing capacity
连接槽尺寸 Dimension of connecting channel
连接尺寸 Conncetion cimension
连接形式 Type of connection
帘面积 Curtain area
流道面积 Flow area
流道直径 Flow diameter
流量孔板 flow orifice plate
流量控制阀 flow control valve
流量特性 Flow characteristics
流量特性偏差 Flow characteristics derivation
漏汽量 Steam loss
脉冲式疏水阀 Impulse steam trap
密封面 Sealing face
密封试验 Seal test
密封试验压力 Seal test pressure
明杆平行式双闸板闸板 Double Disk Parallel Gate Valves
明杆闸阀 Outside screw stem rising through handwheel type gate valve
膜片 Diaphragm
内压自封 Pressure seat
逆止阀；止回阀 check valve
逆止阀；止回阀 non-return valve
逆止阀;止回阀;单向阀 check valve
排放背压力 Brilt-up back pressure
排放压力 Relieving pressure
排灰阀 Ash valves
排量系数 Coefficient of discharge
排气阀 air release valve
排气阀 Exhaust valves
排气阀 Vent Valve
排水阀 Drainage valves
排水温度 Temperature at discharging condensate
排污阀 blowdown valve
排污箱(阀) Waste Valves
排渣闸阀 Scum Gate Valves
盘阀 moushroom valve
盘状阀 plate valve
旁路阀 by pass valve
配汽活塞阀缸套 piston valve line
喷射阀 injection valve
喷射阀 sprayer valve
喷水阀 spray water valve
频跳 Chatter
平衡阀 Balance valves
平衡式 Balance type
平行式闸阀 Parallel gate valve Parallel slide valve
启闭件 Disc
启闭压差 Blowdown of a safety valve
起始升程 Commencement of lift
气动装置 Pneumatic actuator
气阀摇臂 valve arm
气－液动装置 Pneumatic-hydraulic actuator
潜水电泵(排污泵) Submerged Motor Pumps
切断阀;截止阀 block valve;shut-off valve;stop valve
切断式止回阀 stop check valve
切换阀;多向阀 changeover valve
球、球芯 Ball
球阀 Ball valve
球阀 globe valve
球体 Ball
全启式安全阀 Fall lift safety valve
热凝结水排量 Hot condensate capacity
入口隔离门 suction isolating valve
塞子 Plug
三通阀 three-way isolating valve
三通阀 three-way valve
三通式 Three way type
上密封 Back seat
上密封试验 Back seal test
渗漏量 Leckage
升降立式止回阀 Vertical lift check valve
升降式止回阀 Lift check valve
适用介质 Suitable medium
适用温度 Suitable temperature
手摇油泵(阀) Manual Oil Pumps Valves
疏水阀 drain valve
双金属片式疏水阀 Bimetal elements steam trap
双口排气球 Double Opening Exhaust Valves
双联弹簧式安全阀 Duplex safety valve
双闸板 Double gate disc
双闸板平板闸阀 Double Disc Flat Gate Valves
水封闸阀 Water Seal Gate Valves
水力喷射器(真空泵) Vacuum Pumps
伺服阀 servovalve
填料 Packing
填料垫 Packing seat
填料函 Stuffing
填料式旋塞阀 Gland packing plug valve
填料箱 Stuffing box
填料压盖 Gland
通气阀 breather valve
通气阀；呼吸器 breather
通用阀门 General valve
吐出阀；排出阀 discharge valve
吐出阀限位器 delivery valve guard
微启式安全阀 Low lift safety valve
微阻缓闭止回阀 Tiny Drag Slow Shut Check Valves
吻合度 Percent of contact area
蜗轮传动蝶阀 Butterfly Valves with Gear Actuator
蜗轮传动装置 Wormgear actuator
屋脊式隔膜阀 Weir diaphragm valve
无阀泵 valveless pump
无阀隔膜泵 valveless diaphragm pump
无阀振动泵 valveless vibration pump
无负荷漏汽量 No-load steam loss
无负荷漏汽率 Rate of no-load steam loss
吸（抽）气阀 Aspirating valves
吸入阀 suction valve
吸入阀限位器 suction valve guard
先导式安全阀 Pilot operated safety valve
先导式液压阀 Pilot-operated recing valve
相对静偏差 Relative static characteristics derivation
相对流量特性偏差 Relative flow characteristics derivation
相对压力特性偏差 Relative pressure characteristics derivation
销轴 Hinge pin
楔式闸阀 Wedge gate valve
斜板式蝶阀 Indined disc butterfly valve
泄料（放空，排污）阀 Blowdown valves
泄压阀 Decompression valves
泄压阀 pressure release valve
泄压阀；安全阀 relief valve
卸荷式减压阀 Balanced recing valve
型号 Type Model
旋启多瓣式止回阀 Multi-disc swing foot valve
旋启式止回阀 Swing check valve
旋启双瓣式底阀 Double disc swing foot valve
旋塞阀 Cock
旋塞阀 plug valve
压力（増压）阀 Pressure valve
压力调节阀；压力控制阀 pressure controlled valve
压力特性 Pressure characteristics
压力特性偏差 Pressure characteristics derivation
压力增长系数 Pressure increasing ratio
摇杆 Arm
液动装置 Hydraulic actuator
液化气管件 LPG Pipe Fitting
液下泵 Under Water Pumps
液压执行器 hydraulic actuator
仪表针形截止阀 Meter Needle Type Globe Valves
溢流阀 overflow valve
翼形阀；锥形阀 wing valve
油封式旋塞阀 Lubricated plug valve
有阀翼板 double acting wing
有阀翼板 wing with valve
有负荷漏汽量 Load steam loss
有负荷漏汽率 Rate of load steam loss
圆板阀；圆盘阀 disc valve
圆盘式疏水阀 Shemostatic team trap
圆柱齿轮传动装置 Cylindrical gear actuator
圆锥齿轮传动装置 Conical gear actuator
闸板 Wedge disc
闸板式隔膜阀 Wedge diaphragm valve
闸阀 gate valve
闸阀 sluice valve
针形阀 Pintle valve ; Needle valve
真空破坏阀 vacuum breaker valve
蒸汽疏水阀 Automatic steam trap Trap
整定压力 Set pressure
正向作用式减压阀 Direct acting recing valve
支架 Yoke
直接载荷式安全阀 Direct loaded safety valve
直接作用式减压阀 Direct-acting recing valve
直流式 Y-globe type
直流式截止阀 Oblique Stop Valve
直通单向阀 inline check valve
直通单向阀 straightway check valve
直通阀 Throughway Valve
止回阀 Check Valve
止回阀；回流阀 reflux valve
制动阀 Brake valves
中压阀门 Middle pressure valve
钟形浮子式疏水阀 Inverted bucket steam trap
钟形罩 Inverted bucket
轴套 Axis Guide
主阀 Main valve
主要外形尺寸 Prime out-form dimensions
主要性能参数 Specifeca tion speeification
注液漏斗阀 Priming Tundish Valve
柱塞阀 Plunger valve
柱塞截止阀 Plunger Globe Valve
柱塞型摆动阀 rocking plunger valve
撞击手轮 Impact handwheel
锥形阀；翼形阀 conical valve
自动循环阀 Automatic Recirculation Valve
组合阀 Combination valves
最大过冷度 Maximum subcoold temperature
最大流量 Maximum flow rate
最大压差 Maximum differential pressure
最低工作压力 Minimum operating pressure
最高背压率 Maximum rate of back pressure
最高工作背压 Maximum operating back pressure
最高工作温度 Maximum operating temperature
最高工作压力 Maximum operating pressure
最高排水温度 Maximum temperature at discharging
最高允许温度 Maximum allwable temperature
最高允许压力 Maximum allowable pressure
最小过冷度 Minimum subcooled temperature
最小压差 Minimum differntial pressure

『拾』 有懂阀门技术英文用语的来帮帮忙

这还不容易么 看我的翻译 如果可以你就采纳我的答案噢~~~！！
Titanium Valves: 1. General shall not, without permission Party casting welding repair process. 2. Material forged titanium material shall be ASTM B381 Gr. F2, or Gr. F3. Casting titanium material shall be ASTM B367 Gr. C2, or Gr. C3. Titanium components, the maximum iron content of 0.07% and the maximum hydrogen capacity of 60ppm. Casting the mechanical properties of casting resie to comply with ASTM requirements. Stick Titanium Standard ASTM B348 Gr.5. 3. X-ray detection casting is subject to 100% X-ray detection test, based on ASTM E446 Class A, B, C 2-class standards, with no D, E, F. 4. Penetrant testing all the casting in the stress test carried out after the required 100% of the permeability test, in order to avoid casting the cracks, trachoma and so on. 5. Certificate B must provide a detailed mechanical performance testing, physical testing, chemical composition of reports and documents.  Hastelloy alloy valve 1. Castings Hastelloy Castings Hastelloy C4 and the need to use ASTM A494 Grade CW-2M of the alloy, the largest iron content does not exceed 2%. If you specify the use of Hastelloy C276, Ze Xu using UNS N10276 alloy, mechanical properties required to meet the ASTM minimum requirements. 2. X-ray detection for each casting is subject to ultrasonic or X-ray detection. After each batch and then take 10% of the testing, the nominal diameter greater than or equal 6 "of the body in need of complete testing, greater than or equal 8" in key parts of the body just for testing. -Ray flaw detection test based on ASTM E446 Class A, B, C 2-class standards, with no D, E, F. If you have casting did not meet testing standards be admitted to the batch number of the additional testing. If these two happen again does not meet state testing standards, then take all of the batch for testing. 3. Penetrant testing a batch of each supplier is required to provide penetration testing report at the same time need to provide mechanical tests, physical tests and chemical composition of reports. 4. Certificate B must provide a detailed mechanical performance testing, physical testing, chemical composition of reports and documents.  al-phase steel valves: 1. A al-phase steel all of the components required to meet the ASME V111, Div 1, Appendix 7 requirements. 2. Material Duplex steel castings for example, to comply with ASTM A995 Grade 4A for 2205 alloy, grade 6A for the 2507 alloy. Chemical composition, mechanical properties to meet the requirements of subparagraphs 3 to 5. 3. Chemical composition of the amount of corrosion-resistant plex steel (PREN) according to the formula: PREN = (Cr wt% + 3.3 Mo wt% + 16 N wt%), calculate the value of not less than the following. 2205 Alloy - 34 2507 Alloy - 40 4. Chemical composition requirements are as follows Material 2205 Alloy 2507 Alloy maximum carbon content of 0.030% 0.030% chromium content of 21.5-23% 24-26% nickel content of 4.5-6.5% 5.5-8.0% Mo content of 2.9 -3.5% nitrogen content of 0.145-0.2% 3.6-4.0% 0.24-0.35% maximum sulfur content of 0.02% 0.02% maximum phosphorus content of 0.03% 0.03% maximum silicon content of 1.0% 0.8% maximum manganese content of 2.0% 1.5% tungsten content of 0.5% maximum 0.8% maximum copper content of 0.5% 0.75% 5. mechanical properties requirements are as follows Material 2205 alloy 2507 alloy minimum tensile strength of 620MPa 700MPa 0.2% deformation deflection (minimum) 450 MPa 550MPa Elongation (2in%) 25min 15min maximum stiffness of 290 BHN (30.5 Rc) 310 BFN 6. The remaining test casting heat treatment, the need to use samples of the following tests. Testing methods and the use of the standard details of the Party should be provided. Tension Test    Impact Test hardness testing  corrosion testing 7. Non-destructive testing, after the final heat treatment in accordance with the following annotation can be seen in non-destructive testing penetration testing X-ray detection range of 100% 100% testing a key component of the valve based on ANSI B16 .34 standard ASME VIII Div 1 App 8 ASME VIII Div 1 App 7 processes ASME VIII Div 1 App 8 ASME VIII Div 1 App 7 acceptance ASME VIII Div 1 App 8 ASME VIII Div 1 App 7
可以吧